Table of Contents
We’ve included the complete Moen Shower Valve Installation process and some really useful tips and tricks that will make setup a breeze.
Thanks to Moen’s simplified cartridge design, users can choose from a range of single-handle valving systems used in washrooms, sinks, kitchen sinks, bathtubs, and showers. Moen’s method is cost-effective because it lasts long and has expensive cartridges.
Additionally, the organization still produces 40-year-old components that are used in valve systems. This implies that it will not be hard to discover new elements.
Plumbers with experience should do setup and restoration, specifically when you lack confidence in the handyman’s abilities. But if you’re confident that you can manage it, go on.
Complete Moen Shower Valve Installation Process
Below is the complete installation process of Moen Shower Valve. Read till end and fix it by yourself.
- Disconnect the major water supply and find the piping access panel. Contact your neighborhood plumbing expert unless you’re unsure where or how to look for them.
- Join the showerhead valve to the cement floor that you can place against the bathtub side. Ensure the valve is placed 32″ away from the bathtub’s base to guarantee correct functioning.
- With the help of a ½ copper connection, secure the new valves to the dropping exit leading to your bathtub.
- Apply thread sealing tape to the valve’s entry and exit points, wrapping it on them counterclockwise. It would help if you then used an adjustment wrench to secure the ½ female threading to the PEX adapter installed.
- A crimp ring will be used for every connector when attaching the valves to the warm and chilled water inlets and the present showering risers exit. Before installing a connection tube, attach a coupler. Utilize a crimp tool to seal the connector.
- Take out the cement floor, detach the retention clip, and use pliers to extract the cartridges from the showering valve. The bathtub dropping outlet connector may then be welded.
- Activate your house’s water supply and let the water flow for approximately 15 seconds. This will cleanse the systems and reveal whether any connectors have leaks.
- Reinstall the cartridge using the notched end after turning off the supply of water.
- Install the walls plate for the showerhead. Don’t forget to place the plumber’s glue on the flange’s rear, thread sealing tapes at two ends, and push the flange into the walls after threading the showering arm into its appropriate location.
- Use the wrench to secure the showering head’s screws. Attach the bathtub spout after that.
- To connect the showering valve, put the top tube onto the valves and next screw the escutcheon into place. Assure the warm and chilled are placed correctly.
- Check the water’s temp after that. Make sure the temperature is 120 ° or lower.
Some Useful Tips
Think about the showerhead’s length for you and every family member.
How would you like it to be placed? Do you have to relocate any existing pipes?
- To prevent water from falling on the ground, ensure the faucet, wall-mounted, body sprayer, or it faces far from or close to the bathroom door.
- Another important factor to consider is if you want to prevent mildew or fungus in the showering area, you must have a good ventilation system.
- Your best defense against germs, mold, and mildew is air movement. Mold is immune to ventilation, so adding exhaust fans and dehumidifiers can help maintain the shower area free of unwanted development.
When Should A Shower Valve Be Replaced?
In order to avoid a leaking shower as early as possible, you should change the showering valve. With time, a leaky valve greatly increases the wastage of water in the house, raising overall utility costs. Additionally, there may be a chance that a concealed valve might leak, which could result in significant water leakage and mold expansion is present behind the bathroom wall.
Shower efficiency is enhanced whenever a shower valve is replaced. A brand new stress balance valve fixes the issue of showering water temperatures changing when the restroom flushes or even other faucets in the house are used.
Families who update their shower valves also benefit from comfort and security. Install thermostatic valves and pre-set showering water temps. A thermostat valve reduces the requirement for minute changes to get the ideal temperature!
It also ensures water doesn’t become too hot; this is crucial in households with young kids or aged people since they are more prone to burning and scalding from heated water.
Adjust Your Water Heater To Avoid Getting Into Hot Water!
Examine the water heater prior to starting your bathroom renovation. Consult a qualified plumber about:
- Heating systems can be either tank or tankless.
- Usage of less energy
- Tank pumps have set capacities.
- How many individuals reside in your houses?
- Life expectancy and upkeep
- It helps to consider the water heater when organizing the installment of a shower. It seems that it is fairly worthless if the water heater doesn’t supply you with enough hot water to consume during your shower!
Frequently Asked Questions (FAQs)
Which shower head best suits your needs?
Everybody seems to have their own preferences. Think about which shower head best meets your needs: hand-held, body sprayer, wall-mounted, or rainfall.
Which materials will you use?
Brass, bronze, nickel, or copper? They are all distinct from one another in terms of aesthetics and how they respond to moisture in a continual state.
Which types of water valves need to be installed?
Yet another consideration is selecting the shower valve type that best meets your needs.
Whenever you switch on the faucet, several valves might affect the flow and temperature of the water. Also, don’t forget to consider your family’s other members, particularly the young and the elderly.
What is the Moen shower valve installation process?
The installation process is simple; read the above process, and you’ll know what to do.
