How To Install Single Bowl Sink With Garbage Disposal?

The kitchen and bathroom are the most important places that we use the most. So, they should be properly clean and sanitized. Our kitchen has a lot of garbage such as a wrapper, food wastes, and many more that should dispose of.

Tired of picking up leftover food from your sink drainer?

Is it a chore for your household to scrape the dishes in the trash? 

And how about removing burnt crude from the bottom of your pots and pans without clogging your sink drain?  

This is too much difficult and time-wasting, to dispose of the wastes on daily basis. In our busy lives, it is hard to make our living place clean. Therefore, in this runny life, we have to put something in our house or in our kitchens that automatically dispose of the garbage off.

For a long time, you undoubtedly wanted a trash can, hoping that it would make it much easier to clean your dishes and pots.

For this purpose, a single bowl sink with garbage disposal is used in many households. This will be very helpful for our kitchen these days. You may also learn more about garbage disposals on GarbageFix website.

Installing disposal on a single sink is much easier because you won’t have to manage the link from the second sink. With a few basic hand tools, you can install a trash can in a single sink in a matter of hours.

On the circuit breaker, turn off the circuit breaker that contains the garbage disposal switch. Then place a non-contact electrical tester against the garbage disposal wires under the sink. When the tester light comes on, turn off other circuit breakers until the tester confirms that the circuit is dead.

With a large pair of sliding joint clamps, loosen the two couplings that hold the bottom of the P trap and the drain extension pipe under the sink and set aside the drain sections. To keep drain odors at bay, slide a towel into the exposed drain pipe.

Use a sliding joint clamp to loosen the nut at the bottom of the drain coupling and loosen it. Then, when pushing the clutch up, lift the drain flange from the bottom of the sink.

Use a plastic putty knife to scrape the old plumber’s putty out of the drainage hole. Apply a plumbing putty bead to the rinse flange of a new garbage disposal system and install the flange evenly in the rinse hole.

Under the sink, slide the gasket and retaining ring onto the exposed flange sleeve, then over the assembly ring and snap ring. Tighten the three screws evenly until the assembly is firmly attached to the bottom of the sink drain. Wipe off any additional plumbing putty that escaped from the sink seal.

If you have a dishwasher that needs to be connected to the disposal, use a screwdriver and hammer to remove the knockout plug from the dishwasher on the side of the disposal body.

Remove the cover from the metal compartment by tightening the screw. To secure the cable, plug about six inches of electrical cable from the wall switch into the wire terminal into the elimination cable compartment, then tighten the clamp with a screwdriver.

On the ripper, cut the outer coating of the six-inch cables into the metal compartment. Use a pair of strippers to remove 1/2 inch insulation from the black and white wires.

Use a wire nut to connect the black wire from the cable to the black wire from the disposal. Connect the white wires in the same way, then wrap the bare wire around the green grounding screw with a screwdriver and tighten the screw. Replace the lid and store the wires in the chamber.

Place the disposal unit in the assembly system and drag it. To attach the disposal unit to the bracket, rotate the disposal body so that the outlet faces the drainpipe, and then tighten the mounting bracket.

Manually tighten the connection between the discharge pipe and the outlet during final disposal. Remove the cloth and connect the drain pipe and the discharge hose to the P-trap and extension hose. Tighten all connectors with the sliding attachments.

Tighten the switch to attach the dishwasher drain hose for disposal and connect it to the dishwasher discharge (if applicable). Switch on the elimination circuit breaker. Turn on the sink faucet and test the removal unit with the wall switch.

There are so many benefits of garbage disposal with a single bowl sink. Here I have some benefits of installing a single bowl sink with garbage disposal:

1. When you throw away less food, fewer rodents, and other creatures are passing through your garbage. When there is less garbage in the garbage, you don’t have to worry about the smell of garbage rot in the kitchen.
2. Waste management breaks down food before it enters the drain, preventing blockage and speeding up the dish-washing process.
3. Installing wastewater in the sink speeds up washing and waste management.
4. Bottom food waste causes less damage to the drainage pipe, resulting in fewer situations that may require emergency pipe repairs.
5. Disposal allows you to flush more of your food waste into the drain, reducing the amount of waste you produce for the landfill and making it more environmentally friendly.
6. Installing garbage disposal equipment in your sink speeds up dish-washing and waste disposal.

Since installing disposal in a one-bowl sink is easier, it is more cost-effective. The cost of a disposal unit is determined by its brand and model. Some models are as low as $85, while others cost more than $200.

Labor costs between $80 and $200, depending on who you employ, so installing the system itself is less expensive. The total cost of buying a device and hiring someone to install it averages about $266.